BROADCAST
EPOXY FLOORING
DESCRIPTION:
Bedrock
BROADCAST EPOXY FLOORING is a 100% solids (solvent & water free),
three component, color through, epoxy flooring system primarily used for
finishing concrete or plywood floors. It
provides a sealed, seamless, non-porous, easily maintained finished surface,
ranging from approximately 70 - 125 - 250 mils thick.
SYSTEM COMPONENTS:
Bedrock
BROADCAST EPOXY
FLOORING incorporates state of the art epoxy resins to chemically fuse
aggregates into a multi-coat, high build flooring system (based on usage
requirements.) It consists of
Cure & Seal Primer (optional for porous substrates), Bedrock Flexi-Coat
waterproof membrane (if
required), Bedrock Binder for broadcast coats,
Rockote (topcoat) and CRU1 (optional topcoat for added chemical
resistance and color stability.)
GRADES AVAILABLE:
Solid color (with pigmented epoxy) or multicolored quartz (with clear epoxy.) Smooth, medium, or slip resistant finish textures available. Please note recommended thickness for multicolored quartz is 125 mils or thicker.
APPLICATION:
Follow instructions
for preparation and mixing of component materials. Apply primer and allow to
cure. Apply Bedrock Flexi-Coat, if waterproof membrane is required. Allow to
cure. Apply Bedrock Binder neat. While still wet, fully broadcast aggregate to
excess. Allow to cure.
Sweep and vacuum excess aggregate. Apply Bedrock Binder neat (for high
build systems repeat this step.) While still wet, fully broadcast aggregate
again and allow to cure. Sweep and vacuum excess aggregate and apply Bedrock
Rockote as a topcoat. Allow to
cure. Apply Bedrock CRU1, if required, and allow to cure.
BROADCAST
EPOXY FLOORING
PHYSICAL PROPERTIES / TECHNICAL DATA
| Compressive Strength (ASTM D695) | 10,500 psi minimum @ 7 days |
| Tensile Strength (ASTM D 638) | 1750 psi minimum |
| Tensile Elongation (ASTM D 638) | 3 percent |
| Tensile Shear | 28 days @ 77 F. 1800 psi minimum |
| Hardness Shore D (ASTM D 2240) | 85 - 90 |
| Flexural Strength (ASTM C 882) | 4,500 psi |
| Bond Strength (ASTM C 882) | 100% concrete failure |
| Indention (MIL-D-3134F) | No Indention |
| Abrasive Resistance (ASTM D 1044) | .19 gram maximum |
| Water Absorption (ASTM C 413) | .1% |
With CRU1 Top Coat:
Pencil Hardness
2H
Taber
Abrasion
CS17
1,000 gms, 1,000 cycles wt loss
50 mgs
CHEMICAL RESISTANCE:
Resistant to mild
acids, alkalies, detergents, solvents, skydrol, hydraulic fluids, lubricating
oils, deicing salts, etc. CR and CRU1 have higher resistance
to certain chemicals. See individual data sheets.
“Warranties: Seller
warrants that its goods, as described on the face hereof, are free from any
defect in material or workmanship. Seller
makes no other warranty, expressed or implied, and all implied warranties of
merchantability and fitness for a particular purpose are hereby disclaimed.
Seller shall not be liable for prospective profits or special indirect or
consequential damages. Seller’s
sole liability and buyer’s exclusive remedy for breach of any warranty is
expressly limited, at seller’s option, to replacement at the original F.O.B.
point or refund of purchase price. Seller
shall not be responsible for any claim resulting from failure to utilize product
in the manner in which it was intended and in accordance with instructions
provided for use of product. Any
claim for breach of warranty shall be deemed waived unless buyer shall give
seller written notice of such claim within (60) days after delivery and shall
allow seller reasonable opportunity to investigate claim and inspect product.”