[ Flexi-Coat ] [ Bedrock Binder ] [ Rockote ] [ Best Cleaner/Degreaser ] [ Stone Saver ] [ Safety Grip ] [ Troweled Epoxy Flooring ] [ Cementious Self-Leveling ] [ Broadcast Flooring ] [ Bedrock Patch ] [ Cure & Seal ]

 Flexi Coat

DESCRIPTION:

Flexi-Coat is a 100% Solids Epoxy Waterproof Membrane finished surface.   Flexi-Coat provides a blush free, fast cure coating with excellent adhesive abilities.  It is available in clear and a variety of colors.  Fabric reinforcement is not required when installing this system.  

 USE:

Waterproofing, sealing, patching and coating of surfaces that are exposed  to the stresses of impact or thermal change.  Flexi-Coat can be used as the matrix for an aggregate system, or a stand alone coating where a greater degree of elongation and flexibility is required.  Various textures are available, ranging from skid-resistant to smooth.

  1. - Mechanical Equipment Rooms

  2. - Pedestrians and Traffic Decks

  3. - Waterproof Membranes under other finished flooring

  ADVANTAGES:

Provides flexibility and elongation to absorb impact.

Highly resistant to chemical and water spills.

Does not require fabric reinforcement within the matrix.

Finished system in and of itself.

Blush free, fast cure and excellent adhesive abilities.

  LIMITATIONS:

Do not apply at temperatures below 50 degrees F.

Mix only amount that can applied in 15 minutes.

Surface must be properly prepared before application.

 

BEDROCK “FLEXI-COAT”

PHYSICAL PROPERTIES / TECHNICAL DATA

Mix Ratio  1:1 by volume
Pot Life  20 mins. @ 77 degrees F.  
Initial Set Time  6-8 hrs. @ 77 degrees F.  
Color  Clear or Pigmented  
Shore D Hardness (ASTM D 2240-86)  55  
Tensile Strength (psi) (ASTM D 638-86)  1,530
Tensile Modulus (psi) (ASTM D 638-86) 33,800  
Tensile Elongation (%) (ASTM D 638-86)  55
Tear Strength (lb/in) (ASTM D 1938) 82  
Water Absorption (ASTM C 413)   .1%  
Coverage (16 mils thick)  100 sq.ft/gallon (theoretical)  
Shelf Life  2 Years in unopened container  

   

INSTALLATION:

CLEANING: Area must be clean, sound and dry.  Conventional cleaning methods used are acid etching, shot-blast, or aqua-blast.  Dense concrete should be acid etched exposing small aggregate particles and giving the appearance of sandpaper.

PRODUCT MIXING:

1. Stir each component separately.

2. Blend 1 part base to 1 part reactor by volume and mix completely.  

“Warranties: Seller warrants that its goods, as described on the face hereof, are free from any defect in material or
 workmanship.  Seller makes no other warranty, expressed or implied, and all implied warranties of merchantability 
and fitness for a particular purpose are hereby disclaimed.  Seller shall not be liable for prospective profits or special 
indirect or consequential damages.  Seller’s sole liability and buyer’s exclusive remedy for breach of any warranty is 
expressly limited, at seller’s option, to replacement at the original F.O.B. point or refund of purchase price.  Seller shall 
not be responsible for any claim resulting from failure to utilize product in the manner in which it was intended and in 
accordance with instructions provided for use of product.  Any claim for breach of warranty shall be deemed waived 
unless buyer shall give seller written notice of such claim within (60) days after delivery and shall allow seller reasonable 
opportunity to investigate claim and inspect product.”  
 

Email: info@bedrockresin.com            sales@bedrockresin.com

Bedrock Resin Corp. 164 Central Avenue, Farmingdale, NY 11735 1 (866) 345-EPOXY Toll Free