BEDROCK
PATCH
DESCRIPTION:
Bedrock Patch is a two component, equal volume mix with
thoroughly dispersed fillers and aggregate pre-blended into the system.
It is a 100% solids epoxy product that contains no solvents or water. Bedrock Patch is a high viscosity, non-sag epoxy paste.
USE:
Bedrock Patch was designed for general repair and
maintenance of concrete, masonry and properly secured plywood.
It is ideal for filling cracks, voids and other defects in concrete,
brick or block structures. The
bond strength far exceeds that of concrete.
Bedrock Patch provides total waterproofing.
It can be used as a sealer around the periphery of below grade areas at
the junctures of walls and floors. Bedrock
Patch has excellent adhesion and is non-shrinking, which assures permanent
repairs of small holes, depressions and spalled areas.
ADVANTAGES:
 | - Fill in holes, cracks and spalls for smoother surface. |
| - Can be applied thin of thick. |
| - Can be used on concrete, plywood, brick, stone and any
other clean surface. |
| - Its non-sag abilities makes it ideal for vertical
portions. |
GRADES AVAILABLE:
| - Fine, for thin patching. |
|
-
Course, for heavy patching. |
|
- Natural or standard colors. |
|
-
Fast cure, ready for traffic in 2 - 4
hrs (@ 77 deg. F) |
LIMITATIONS:
Exposure to temperatures exceeding 150 degrees for long
periods of time is not recommended.
BEDROCK PATCH
PHYSICAL PROPERTIES / TECHNICAL
DATA
| Mix Ratio | 1:1 by volume |
| Pot Life | 1 hour @ 77degrees F. |
| Initial Set Time | 6 - 8 hours @ 77 degrees F. |
| Color | Concrete Grey |
| Compressive Strength (ASTM D695) | 8,000 psi minimum |
| Tensile Strength (ASTM D 638) | 3,000 psi minimum |
| Tensile Elongation (ASTM D 638) | 3 percent |
| Tensile Shear | 28 days @ 77 F. 1800 psi minimum. |
| Hardness Shore D (ASTM D 2240) | 75 |
| Viscosity | Non-Sag Paste |
| Shelf Life | 2 years in unopened container |
CHEMICAL RESISTANCE:
Resistant to mild acids, alkalies, detergents, solvents,
skydrol, hydraulic
fluids, lubricating oils, deicing salts, etc.
SURFACE PREPARATION:
Surface must be clean, sound and dry.
Dirt, dust, rust, oils, old coatings and other contaminants should be
removed before applying Bedrock Patch. The
best methods for preparing the surface are shotblasting, mechanically grinding,
or acid etching.
MIXING INSTRUCTIONS:
1. Blend equal volumes of base with reactor.
2. Mix thoroughly with a slow speed drill equipped with a mixing paddle. Be sure to mix sides and bottoms of container
3. Bedrock Patch should be a uniform streak-free color when mixed
properly.
PACKAGING:
Standard Packaging: 1 Gallon Part A : 1 Gallon Part B in a carton.
Available: Quarts, ½ Gallons, 2 Gallon Pails, 5 Gallon Pails
“Warranties: Seller warrants that its goods,
as described on the face hereof, are free from any defect in material or
workmanship. Seller makes no other
warranty, expressed or implied, and all implied warranties of merchantability
and fitness for a particular purpose are hereby disclaimed.
Seller shall not be liable for prospective profits or special indirect or
consequential damages. Seller’s sole liability and buyer’s exclusive remedy for
breach of any warranty is expressly limited, at seller’s option, to
replacement at the original F.O.B. point or refund of purchase price. Seller shall not be responsible for any claim resulting from
failure to utilize product in the manner in which it was intended and in
accordance with instructions provided for use of product.
Any claim for breach of warranty shall be deemed waived unless buyer
shall give seller written notice of such claim within (60) days after delivery
and shall allow seller reasonable opportunity to investigate claim and inspect
product.”