TROWELED
EPOXY FLOORING
DESCRIPTION:
Bedrock TROWELED
EPOXY FLOORING is a 100% solids (solvent & water free), three component,
color through, epoxy flooring system primarily used for finishing concrete or
plywood floors. It provides a
sealed, seamless, non-porous, easily maintained finished surface,
approximately finish thicknesses from 3/16" - 1/4" thick.
SYSTEM COMPONENTS:
Bedrock TROWELED
EPOXY FLOORING incorporates state
of the art epoxy resins to chemically fuse aggregates into a multi-coat, high
build flooring system (based on usage requirements.)
It consists of Cure & Seal Primer (optional for porous substrates),
Bedrock Flexi-Coat waterproof membrane
(if required), Bedrock Trowel COAT, Rockote
(topcoat) and CRU1 (optional topcoat for added chemical resistance and color
stability.)
GRADES AVAILABLE:
Solid color (with pigmented epoxy) or multicolored quartz (with clear epoxy.) Smooth, medium, or slip resistant finish textures available.
APPLICATION:
Follow
instructions for preparation and mixing of component materials. Apply primer
and allow to cure. Apply Bedrock Flexi-Coat, if waterproof membrane is
required. Allow to cure. Trowel a mortar mix of Bedrock Trowel Down to
required thickness (mix epoxy first, as instructed on the label, and add
aggregate to a ratio of 1 part epoxy to
3 parts of aggregate to create an epoxy mortar.
Blends of specially graded aggregate (either natural or colored) are
available. Mix with a slow speed
high torque drill until uniform.) Epoxy
mortar may be hand troweled or power troweled. Allow to cure over night.
For slip-resistant texture apply Bedrock Binder neat. While still wet,
fully broadcast aggregate again and allow to cure. Sweep and vacuum excess
aggregate and apply Bedrock Rockote as a topcoat.
Allow to cure. Apply Bedrock CRU1, if required, and allow to cure.
TROWELED
EPOXY FLOORING
| Compressive Strength (ASTM D695) | 10,500 psi minimum @ 7 days |
| Tensile Strength (ASTM D 638) | 1750 psi minimum |
| Tensile Elongation (ASTM D 638) | 3 percent |
| Tensile Shear | 28 days @ 77 F. 1800 psi minimum |
| Hardness Shore D (ASTM D 2240) | 85 - 90 |
| Flexural Strength (ASTM C 882) | 4,500 psi |
| Bond Strength (ASTM C 882) | 100% concrete failure |
| Indention (MIL-D-3134F) | No Indention |
| Abrasive Resistance (ASTM D 1044) | .19 gram maximum |
| Water Absorption (ASTM C 413) | .1% |
With CRU1 Top Coat:
Pencil Hardness
2H
Taber Abrasion, CS17
1,000 gms, 1,000 cycles wt loss 50 mgs
CHEMICAL RESISTANCE:
Resistant to mild
acids, alkalies, detergents, solvents, skydrol, hydraulic fluids, lubricating
oils, deicing salts, etc. CR and CRU1 have higher resistance
to certain chemicals. See individual data sheets.
“Warranties: Seller
warrants that its goods, as described on the face hereof, are free from any
defect in material or workmanship. Seller
makes no other warranty, expressed or implied, and all implied warranties of
merchantability and fitness for a particular purpose are hereby disclaimed.
Seller shall not be liable for prospective profits or special indirect or
consequential damages. Seller’s
sole liability and buyer’s exclusive remedy for breach of any warranty is
expressly limited, at seller’s option, to replacement at the original F.O.B.
point or refund of purchase price. Seller
shall not be responsible for any claim resulting from failure to utilize product
in the manner in which it was intended and in accordance with instructions
provided for use of product. Any
claim for breach of warranty shall be deemed waived unless buyer shall give
seller written notice of such claim within (60) days after delivery and shall
allow seller reasonable opportunity to investigate claim and inspect product.”